+90 850 549 98 38  ·  info@cybeletile.com

Technical

Product standard, test values, finishes, slip-resistance classes, thicknesses and general installation guidance.

Product Standard and Test Values

Cybele Tile porcelain tiles are produced as dry-pressed porcelain tiles to TS EN 14411 Annex G, Group BIa; they are CE-marked and TSE-certified.

PropertyTest standardRequirementDeclared value
Product classTS EN 14411 Annex GGroup BIa (GL)Dry-pressed porcelain tile
Water absorptionTS EN ISO 10545-3E ≤ 0.5%0.15% (average)
Breaking strength (S)TS EN ISO 10545-4≥ 1300 N (≥ 7.5 mm) · ≥ 700 N (< 7.5 mm)2953 N (average)*
Modulus of rupture (R)TS EN ISO 10545-4≥ 35 N/mm²47.4 N/mm² (average)*
Reaction to fire96/603/EC—A1FL (without testing)
Frost resistanceTS EN ISO 10545-12RequiredResistant
Slip resistanceDIN 51130 / DIN 51097—R9–R13 · A/B/C (on request)
Release of dangerous substancesTS EN ISO 10545-15—Pb < 0.1% · Cd < 0.02%

* Declared values are averages of results measured on 600×1200 mm, 9 mm samples from different production batches; values may vary with thickness and size. Images are indicative; shade and pattern variation between faces is a natural characteristic of the product.

Finishes

Full Lappato

Fully polished surface with high light reflection that brings out the depth of colour and veining.

Lappato

Semi-polished: the surface is partially polished, combining a natural look with a soft sheen.

Sugar Effect

Semi-polished; a lightly textured surface that sparkles in the light thanks to fine crystal grains.

Satin Matt

Silky, soft-touch matt surface with a gentle glow; easy to clean.

Matt

Standard non-reflective matt surface that hides marks. No slip-resistance class is declared for standard matt; specify R9–R13 finishes where slip resistance is required.

R9–R13

Slip-resistance classes, determined under DIN 51130 on an inclined ramp by measuring the angle in degrees at which slipping begins: R9 6–10°, R10 10–19°, R11 19–27°, R12 27–35°, R13 over 35°. For barefoot wet areas, classes A/B/C apply under DIN 51097.

Metallic

A metallic sheen that shifts in tone with the light.

Full Body

Colour and pattern run through the whole body; appearance does not change with wear.

Slip-Resistance Classes

DIN 51130 — shod areas (angle of inclination)

  • R96°–10°
  • R1010°–19°
  • R1119°–27°
  • R1227°–35°
  • R13> 35°

DIN 51097 — barefoot wet areas

  • A≥ 12°
  • B≥ 18°
  • C≥ 24°

Typical use

  • R9Dry interiors
  • R10Entrances, kitchens
  • R11Outdoor, ramps
  • R12–R13Industrial areas
  • A/B/CShowers, pool surrounds

Slip resistance is developed on request; please specify your project requirement when enquiring.

Thickness · Size
  • 5 mmSlim: light, thin application; walls and façades
  • 8 · 9 mmFloors and walls
  • 14 mmAcid-resistant technical tile
  • 20 mmOutdoor floors
Available sizes (cm)
30×60
45×45
60×60
60×120
80×80
90×90
120×120
80×160

Every product in the collection can be produced in these sizes and finishes, independent of its catalogue size. The minimum order quantity for project-specific production is 5,000 m².

General Installation and Care Guidance

Large-size tile installation guide

This guidance is general. Please consult our technical team for project-specific details.

Installation

  • The substrate must be flat, clean, dry and load-bearing; flatness is especially important for large formats.
  • For large-format and slim tiles use a high-performance, deformable cementitious adhesive, applied to both substrate and tile back for full coverage.
  • Tile levelling systems help prevent lippage on large formats.
  • Leave joints even with rectified tiles, and provide movement joints across large areas and at perimeters.
  • Dry-lay tiles from several boxes before installation to see the distribution of faces.

Cleaning and Care

  • After installation, remove cement and grout residues with a suitable grout-residue cleaner.
  • Neutral detergent and water are sufficient for routine cleaning.
  • Do not use abrasive pads or powders on full lappato (polished) surfaces.
  • Products containing hydrofluoric acid damage porcelain surfaces and must not be used.